DIY Audio Home
The "Mighty Midget" (originally in AudioXpress 05/08)
I am now selling PCB's for this project. See my eBay store (seller "pmillett").
UPDATED 12/19/2011 双色球模拟选号器 - I've made some small tweaks to this design and put it on a PCB:
My goal in re-designing the Mighty Midget was to make it as easy to build as possible for a beginner to build. To that end, everything except the output transformers are mounted on the PCB, including the (frightening to a beginner) AC wiring. Though it doesn't guarantee success, it does raise the odds.
双色球模拟选号器i used to make the case for the pcb, using their side profile extrusions. this lets you poke parts (connectors and switches) out both the front and the rear of the box. i also had edcor make a custom pcb-mount choke - is very good at fulfilling requests like that - so you can buy them as well as the transformers from them.
双色球模拟选号器the schematic has changed a little bit. mainly, i used a resistive divider to generate the screen voltage instead of a zener. this removes the power-down instability and squeal that forced me to add a power-up muting relay.
Here is the new PDF schematic, and BOM.
If you want to order the enclosure from Front Panel Express, you can just tell them you want to order their quote # 900825 - that will include the panels, side extrusions, and hardware. Or, you can download my FPE files and customize them (ZIP archive双色球模拟选号器). (If you're observant you might notice that there is an error or two on my chassis - they are fixed in the files).
and some additional photos:
双色球模拟选号器note in the last photo the wire that connects the case to ground. turns out that this is important - without it the amp was noisy and tended to oscillate. so do ground the chassis!
双色球模拟选号器as per usual, i'll sell these pcbs on .
双色球模拟选号器the "mighty midget" is a simple single-ended pentode amp that uses inexpensive compactron tv tubes. it puts out about 3 watts per channel, and uses only one (two-section) tube per channel.
双色球模拟选号器this project was published in audioxpress, may, 2008.
双色球模拟选号器in summary, the amp uses 6t10 tubes, which contain dual-control pentode and power beam tube sections. the dual-control pentode is used as a regular pentode amp (with a trick of biasing up g3 to get linear characteristics). the beam tube section is used in pentode mode, with about 10% plate-to-grid feedback to get decent distortion and damping factor. no global feedback is used.
with a b+ voltage of about 300v, the amp puts out about 3.5w per channel, while dissipating under 10w on the plates of the output tubes. thd at 1w into 8 ohms is about 0.7%. you can see the fft below...
双色球模拟选号器the amp has a modest damping factor, with an output impedance of 3.5 ohms or so. it turns out that this sounds really good into my inexpensive fostex fe164-based speakers, which tend to be a little brassy sounding on a low-output-z amp.
双色球模拟选号器i used small 7k se opt's that i found in akihabara (tokyo), but an xse-10-8-8k should work well, as would a small se opt.
since many of the photos and details are hard to read in the magazine, posted on this page are all the photos, schematic, and mechanical files for you to build this amp. enjoy!
The schematic 双色球模拟选号器 (144kB PDF file)
PDF of the mechanics双色球模拟选号器 (128kB PDF file)
ZIP archive with AutoCAD DWG and R12 DXF files (144kB)
click on the small photos for a full-size photo in grisly detail.
赌博银行转账输了可以要回吗 鑫乐电玩城每天救济金版 快乐12开奖结果查询 时时彩后三直选复式 交会费600的兼职可靠吗